How to fix recliner chair mechanism like an expert by yourself ? This question is still bogging your mind. It isn’t difficult to repair a recliner chair mechanism.
When you be aware of how to install or replace recliner chair mechanism parts perfectly? Here, we put the ten best ways to fix recliner chair mechanism, and you can do it yourself at home. A recliner chairs provide us with comfort whenever we want to relax at home.
You can relax in a recliner chair and watch your favorite TV shows, cuddle your pet or read a book. Like any other furniture in your home, recliners can become damaged. Most of these problems take no time to fix.
How to Fix Recliner Chair Mechanism- The Details Guide
If you want to repair your recliner chair mechanism by yourself, you should know everything about it. Follow these steps to get started. Sometimes, the recliner mechanism can be worn out. Even if it has no signs of wear and tear, the best way to deal with an exhausted mechanism is to replace it. Before you attempt to fix your recliner chair, it is important that you identify the source of the problem. Read the whole article, and you can get more help to fix your recliner chair mechanism. This article will show you how to fix lazy boy recliner chairs.
How to Remove a Recliner Chair Mechanism?
When moving a recliner from one room to another, it may require you to remove the back and re-install it. There are many methods that can be used to move a recliner, but the principles of the process remain the same. First, you have to measure the size of the recliner and establish whether it will fit into the new location. You can remove any locking tabs on your chair with a screwdriver. For bolted on back chairs, remove the panel to expose the bolts.
- Move the recliner chair to the open space. Next, roll the chair onto its front to make it easier to remove back. You can attach the Velcro snaps or strips to the bottom of the recliner chairs.
- You should securely attach to the bottom of the frame, you would like to replace them. After that, find the loop-and-hook to remove the tape attaching the fabric.
- Once you can see the mechanism of the recliner, remove the leather/fabric.
- Look for the metal tabs. Pay attention to the lowest point of the recliner and search for thumb screws.
- Use a flat/standard slotted screwdriver to turn the screws in an anti-clockwise direction.
- Make sure you don’t force them to avoid damaging the threads. Of course, you have to place the screws in a safe location.
If the recliner has metal locking tabs, hold and press the tab firmly and then pull the bottom of the recliner in an upward motion. This metal locking will help to unlock the mechanism. Then, pull the mechanism in an upward direction. If there’s any friction or you have difficulties removing the side of the brackets, move them side by side.
back to menu ↑
How to Re-install a Recliner Chair Mechanism
Re-installing the back of the recliner is a straightforward process. Align brackets at a slight angle. While this might seem difficult at first, it is something you can get used to over time. It takes a lot of effort, especially when the brackets slide into each other. Once you have aligned the brackets correctly, you can push down on the recliner. You can finish by adding screws and adjusting the levers. This will secure the back.
back to menu ↑
How to Fix Recliner Chair Tension Springs?
Any recliner that uses a tension spring. It is possible to replace the tension spring if it does not work. You should replace the tension spring before replacing it. Make sure the spring high quality and it’s strong enough, so it lasts long. If you don’t find the spring of the specific model for the chair, Don’t forget to contact with a manufacturer.. You can also get in touch with the manufacturer for further guidance.
The easiest way to find the problem is by turning over your recliner. This will expose the frame beneath the seat. Other than that, ensure the backrest is in an upright position. Look for clips/tabs at both ends of the spring to determine if it is still in existence. Use a pair of pliers to get rid of the damaged/old spring. This will allow you to disconnect the tension spring form the frame. You must wear safety gear to protect your eyes.
Place the screwdriver on both ends of the spring to pull it apart. Alternatively, you can use nickel to separate the springs. Also, a washer can be used. After that, attach the spring to the frame. Be sure to use a pair of pliers to pull the spring. Now remove the nickel from the coils. But before you perform the task, ensure you’ve attached the spring firmly on both ends. You will need to use pliers for a secure grip.
Once you insert the new spring, put the recliner in an upright position. The easiest way to test the spring on the brackets is to tilt it back. If they don’t offer enough resistance, try a different set. But if you’re comfortable with the tension spring resistance, you can relax and enjoy it. When you follow the tips to the later, you don’t have to call a professional. You should check the model number before you start. Gliding recliners, for instance, have a limited range. You may require the service of an expert to replace the tension springs.
back to menu ↑
How to Fix a Recliner Pull Handle?
If you want to disassemble and repair your recliner handles, have the right tools in your arsenal. You need an ordinary hex key, screwdriver, replacement handle, and a single Torn bit. Apart from that, look at the manufacturer’s model number to be sure you get the right handle. And if you’re still unsure where to buy the replacement kit, you can check the manufacturer’s website. It’s worth mentioning that if the chair is still under warranty, you may get a replacement for free. Please follow these guidelines to replacement handle for lazy boy recliner or other brands recliner pull handle.
Get The New Recliner Pull Handle HERE
Before you begin the process, check if the footrest is in an upright position. Make sure it’s closed before you flip the chair upside down. If the recliner is very heavy, you may need additional assistance. Next, look for the mechanism or screw that holds the chair in its place. Check the screw at its base for most models. Sometimes, it’s inside the recliner at the level of the handle.
- Start to remove the screws using the screw driver from the mechanism.
- Safarat your existing old handle from recliner chair
- After unlocking them, place them at a safe place because you’ll need them again after replacing the new handle.
- Set your new handle, and place the screw at the same point as before.
- You can also tighten the screw using a screw driver.
- Pull the handle gently to prevent ripping off the chair’s cloth.
- You can then look for the decorative part, which is often located below the handle.
- This will allow you to reach the bottom of cable that connects to the chair.
- Pay close attention to cable-end, which is connected to the mechanism.
- Finally, hold your recliner head rest and handle and turn in to normal position from downside floor.
First, install a new decoration plate to replace the handle. Next, insert the new handle exactly like the original one. So, where you’ll fix the mechanism clip back. Take the screws you had removed earlier and insert them to the wooden part to ensure the handle holds in place. Now that you’re done, it’s time to test the handle. Sit on the recliner chair and try to pull the handle. You can also stretch the legs to ensure the chair feels as good as new. The above steps are easy to learn and will save you lots of money if you face problems future.
back to menu ↑
How to Fix Power Lift Recliner Motor?
A electric power lift recliner can take relief to a new stage simply with a push of a button. If your chair doesn’t work, as usual, fix the power lift recliner motor.
- Simple power surges or overloads can damage your recliner chair mechanism
- If the recliner stops in the middle, it means there’s a huge electrical issue.
While you can disassemble the unit and find the disconnected piece, you may have to do more than that.
Buy Now on Amazon
However, if you’ve interest on mechanically inclined, you can solve the problem without additional help – pay attention to details. If you have an electric recliner, make sure you do not catch the cords in the base unit. During the inspection, take an inventory of all the electrical parts. This could include the power supply and activation button, as well as massage motors and lift motors. By making a list, you’ll have a big picture of the whole unit. You don’t want to fix the lift motor only to realize that other parts were faulty.
Since it locates the motor on the underside, use a marker to mark the brackets. This will make it much easier to reassemble the motor. Next, take out the nuts and retain the bolts to the motor drive linkages. After that, remove Torx bolts (2) while securing the motor to the bottom rail. These two small screws should be kept in a separate location. Once you’re done, remove the Torx head screws securing the rail at the rear. Now you can remove the motor.
Remove the four Torx head screws that hold the drive linkages to the motor. It’s worth mentioning that out of the four, and two screws have a large washer. Re-install the left and right drive arms. Don’t forget that the two rear screws must have a washer. Now the motor can be installed. First, you ensure that the pigtail goes to the rear of the chair. Two Torx screws are used to attach the motor to the rail. Remember the two short screws as you attach the front of your motor with Torx screws. The next step is to plug the hand-wand into your recliner motor.
Make sure the ottoman is fully closed by aligning the arms to the drive tube. Use 5/16” bolts to keep the nuts in place. Connect the power cable to the motor pigtail and use black ties to secure it on the rail. Plug your recliner chair into a transformer. Use the complete cycle to test the operation of the chair.
back to menu ↑
How to Fix a Recliner Chair Back?
The back of your recliner may be damaged if it leans too far to one side. It could be an old chair or that it was used too frequently. A broken back can also be caused by uneven padding, a leaning frame or an uneven floor. The basic knowledge and some tools will allow you to fix the recliner’s back mechanism quickly.
A recliner chair can have three types of backs: Bolted on backs, locking lever, or locking tabs. With the locking lever, the brackets attached to the back. These backs were flipped down. The backs must be locked onto the metal posts on the seat. The back must be locked in place to lock the tabs or catch. The bracket fasteners must be removed and tightened. It is much easier to use a screwdriver than your hands.
Bolted-on backs recliner chairs indicate that the back is below the panel. Every model is different so it’s important to know what you are doing before you start. In some models, you may have to use a flathead screwdriver to remove the bolts/screws. That way, it’s much easier to separate the back and the base. After sliding the back on, make sure to tighten the bracket fasteners.
Once you remove the back, turn the chair in an upright position. The back should be reinstalled by raising the arms above the slots. You should lift the back gently to ensure it’s in line with the brackets. For a 3-leg position high-leg recliner, lift the recliners to locate the brackets. Important tip: Make sure the back is properly attached to the body.
The easiest way to test whether you have re-installed the back properly is to move it sideways. If the brackets move around, it is likely that they are not correctly fitted. Be sure to use a slotted screwdriver to push the lever down. Sometimes, loose levers may cause injuries when you don’t handle them carefully. You must also lock each bracket separately. For assistance with fixing a recliner chair’s back, contact a dealer.
back to menu ↑
How to Fix the Swivel Plate Mechanism for Recliner Chair
The movement of a recliner on the surface may cause damage to the swivel base. There may be a pattern of wear, which will vary depending on the use of the seat. You can take steps to make sure the swivel plate remains in top condition. Before you make any repairs to the chair, be sure to identify its model. There are manual and automatic swivels for some recliners. Each part requires a different repair method.
For recommendations on any part that needs replacement, you can refer to the manufacturer’s manual. The underside of your recliner can be accessed by removing the swivel-base. The chair can now be turned on its side. The idea is to see the lower end of the column where it meets with the base. Use a lubricant if you find rust.
In most models, you’ve to find nuts that hold the swivel and the base together. Use a wrench to separate the various components. You can lubricate them if they are very stiff. Separate the bolts from the nuts. Then, pull the base from the support to separate the parts. Sometimes, the swivel issue can be solved by simple bolting and nuts. A general rule of thumb when shopping for a repair part is to ensure that the base can support the weight capacity recommended by the manufacturer. Also, pay attention to the number of ball bearings within the unit.
An existing column can be used as a swivel column base, or a separate column may be provided by a swivel-base. You may have to use a hammer to strike the inner column. This work makes it easier to remove. Be sure to check that all internal parts of the column remain intact before replacing the swivel. Just like in the removal process, the new swivel plate mechanism must align to the holes of the base. The bolts should be inserted and locked with the nuts. Next, use a wrench to tighten them properly. Once you’re done, it’s time for testing.
back to menu ↑
How to Replace Cup Holder of a Recliner
There’s a wide range of recliner cup holders – from plastic to touch LED cup holders. They are designed to create a home theater style and keep your drinks cool as you watch your favorite game/movie. If the button on the cup holder makes a `click’ sound, there’s nothing wrong with it. But if you can’t hear the sound, you have a faulty cup holder. Contact the manufacturer to ensure the best fit. Measure the inner and outer diameter to eliminate the guesswork out of the equation. You should also consider cup height, top height, materials used, color, and colour.
First, remove the warning label. Next, take out the four screws at its base. Keep them safe. You can help others roll the incline backwards with their assistance. Next, remove the cable ties holding the wires. The lounge should be disconnected from the wall. Unplug the cables. The dust cover can be unzipped and the wires placed at the back of your lounge. The cup holder can be removed from the top. Attach the new cup holder to the arm. Keep in mind that you have to feed the wires back into the Velcro loop. Attach the wires together with cable ties and connect them to the frame. This combination will ensure they don’t tangle.
You can close the dust cover zip and cut any loose cable ties. You can roll the seat onto your feet with the assistance of a friend. The bottom four screws holding the cup holder in place should be reattached. Make sure you don’t tighten them too much to avoid damaging the threads. The warning label and plastic cup should be replaced. You should ensure that it is perfectly seated without any protruding.
back to menu ↑
How to Replace a Recliner Mechanism Release Trigger
Maintaining the release trigger on your recliner is a simple DIY task. First, flip it over to expose the bottom part. The tools you need include 11 mm-socket with an extension, wrench, and a screwdriver. The first step is to release the cable from the trigger. You will need to remember which adjustment hole you pulled out, as there are several. Perhaps you can mark it to so you can easily identify once you’re done. You will also be able to see the fill-up rod and the coil spring which cause tension on your trigger.
The bolt, plastic bushing and small tension spring should all be included in the entire component. Replace the nut if it ever gets loose or rusts. You must first consider the length, width, and height of your replacement cable before you purchase it. A standard cable length is 88cm, with an outer spring length of 12.5cm. If you’re doing the manual measurement, be sure to allow for a 0.5 -1” difference. The barrel should measure 5mm (S-shaped). If you’re not sure of the size, get in touch with the manufacturer. High quality cables are made from aluminum alloy. A 90mm spring will fit in most chairs.
You can reinstall the trigger by placing the cable in the hole that you have made. Next, screw the nut. Because you can easily locate the nut inside the mechanism, use a ratchet to tighten it. You should also make sure that the cable is reattached. Once completed the work, place the recliner in an upright position. Test it to ensure everything works perfectly. This works great if you have a recliner.
How to Perform maintenance on the reclining mechanism release trigger.
back to menu ↑
How to Fix a Recliner That Leans to One Side
There are many reasons for your recliner leans on one side. Your wooden frame may become looser over time or the linkage mechanism could be damaged. For uneven flooring or poor padding, your recliner may lean to one side. With just a little knowledge, it is possible to get your chair back into shape. All you need are a few tools to tighten the bolts, nuts, and screws.
Before you begin, make sure that the footrest is securely closed. Next, tilt the recliner forward to expose the underside. For those chairs with an adjustable recliner tension, you’ll find a pair of thumbwheels. While the exact placement may vary, each connected to the tension springs, rotate the wing nuts/thumbwheels to adjust the tension. Rotate the tension spring clockwise to increase tension. And if you want to release it, turn it in an anti-clockwise direction. Your goal should be to adjust the tension to make sure it’s equal on both sides. Use a pair or pliers if the mechanism is too tight.
Sometimes, the screws, springs, and padding may need to be replaced. Find the attachment point and get rid of it. You can also use wood fillings if the contact between the screws or the wooden part is not tight enough. You can also use a matchstick or a toothpick to do this. The mounting spot may become worn if the springs mount to metal.
The springs must have a smooth elastic. The springs should be able to stretch at the exact same level. The screws should not be larger if springs are mounted onto wood. Finally, make sure everything is in order and replace any upholstery.
back to menu ↑
How to Fix a Recliner Footrest
Recliner footrest problem is common thing and you can fix it easily. It can be irreparably damaged if you repeatedly slam down on the footrest of your recliner. A recliner footrest will damaged if it’s caught in one unrelenting position, refuses to lock in place, or doesn’t stay up. You will need a screwdriver and a set of bolts, lubricant oils, and screws to fix the problem. So, follow below these step to fix or adjust a lazy boy power recliner footrest or other brand recliner chair footrest.
If the recliner feels stiff, there’s probably no lubrication. There are also the possibility of loosening bolts and screws. First, flip the recliner upside down. You need to check if the screws/bolts are rusted or loose. If you see any that needs to be replaced or tightened, then do so. You can also replace rusted screws by using new ones. After everything is in order, you can lubricate the joints/bushings at the footrest. Then, try to move the arm up and down. Finally, use a towel to remove the excess grease.
What if there is a problem with the recliner chair’s footrest? It does mean that the adjustable feature doesn’t work. It’s hard to move the footrest, or it could stay the mid-path. Look for a spring-like component that connects the footrest to the bushings. Next, grab a screwdriver and dismantle everything that connects to the springs. Make sure that the spring is removed and all connections are tightened. Check the mechanism to see how it works. If it moves smoothly, then you’ve fixed the footrest recliner problem.
Why is my footrest stuck? If the ratchets don’t work, the footrest will get stuck. There are many ways to approach the issue, depending on the severity of the problem. A wrench, screwdriver and a replacement ratchet are all you need. Place the recliner upsidedown. You will need to disassemble anything that may hinder you from getting to the ratchet. Get the bar out and examine it to ensure it’s not broken. You will need to remove the screws that hold the ratchet in its place. Install the replacement part, if needed. You must ensure that it adjusts each piece. Verify that the footrest moves up and down smoothly.
back to menu ↑
Conclusion
Recliners are not just fun pieces of furniture – it designs them for comfort and rest. The repair process is simple if you are familiar with the features and quirks of recliner chairs. Even if you’ve never repaired a recliner before, it can solve most of the problems easily. Just take the right tools and get down to work. We think this article on how to fix a recliner chair mechanism helped you. So, don’t forget to share it with your friends and family.
You might read also these article:
Guide on How to Fix a Sinking Desk Chair
Simple Ways To Maintain Good Posture When Sitting Long Time
